Address:Building 16, Botong Pioneer Park, Zhongshan Science and Technology Park, Liuhe District, Nanjing, Jiangsu, China

《中华人民共和国电信与信息服务业务经营许可证》苏ICP备13017479号-1

Phone:400-086-4816

Email:20900929@qq.com

Page view:

chemtecone.com

 

》》Chemtec Concrete Protectant

  ChemTec ONE is a high performance, water-based, non-toxic concrete sealer that hardens, strengthens, seals, stabilizes, protects, increases the mass & density and extends the useful life of concrete structures, protecting the concrete structures such as Bridges, Loading Ramps, Driveways, Roads, Runways and Parking Facilities and any concrete structure.

ChemTec ONE, a concrete sealer, is a MULTI-COMPONENT STATE OF THE ART process used for superior concrete protection, that is, a proprietary blend of reactive silicates plus surface active agents, which penetrates into the concrete and reacts with the free calcium and lime to form an insoluble by-product that closes the porosity, increases the mass, strengthens, hardens and seals the concrete, makes it much more durable and resistant to damage by chemicals and mechanical abrasion. The process is non-toxic, non-hazardous, non-flammable. There are no special handling requirements under environmental regulations and contains ZERO% VOC content.

CHEMTEC ONE concrete sealer is designed primarily to protect, harden, dustproof, seal, increase the mass the durability and abrasion resistance of your high strength steel troweled concrete floors and also bridge decks, loading ramps, driveways, runways, fueling stations, tank farms and to increase the useful life of all concrete infrastructures. Do not use on porous concrete blocks or other porous material where there are actual holes in the material.

Upon application the CHEMTEC ONE sealer penetrates into the concrete forming a solid by-product in the gel pores, decreasing the porosity and increasing the mass of the concrete thereby increasing the surface hardness and strength. The process stops solids and liquids from penetrating into the concrete but does allow air molecules to flow freely through the concrete and thus allowing the concrete to "breathe".


》》Main Performance

  CHEMTEC ONE is a MULTI-COMPONENT STATE OF THE ART PROCESS that produces the following results in two applications on brushed finished air entrained concrete, and usually just one application on steel troweled non-air entrained surfaces, by just spraying it on the concrete and letting it dry. (see application instruction methods for all surfaces, especially floors, before using) Steel troweled concrete floors will normally develop a sheen over time.

 

》》CURING OF NEW COCNRETE:

  The process is extremely effective in stopping moisture loss in fresh concrete by applying the process to the concrete as soon as possible after the finish troweling operation (as soon as the concrete is firm and dry enough to walk on with out marking), saturating the surface with the product.

The product immediately reacts with the free lime and calcium, produces a by-product that closes up the pours there by trapping the moisture in the concrete and greatly slowing the rate of evaporation. CHEMTEC ONE sealer can be used as a curing agent and surface hardener on most concrete surfaces. This product is effective at stopping moisture loss in fresh concrete, but does not meet ASTM C-309. DO NOT APPLY TO WET CONCRETE:

 

》》Hardening, dust proofing and sealing of concerete

  Unlike some other concrete sealers the CHEMTEC process actually produces a chemical reaction that creates an insoluble by-product that encapsulates the calcium component of the concrete. It increases the mass and surface hardness of the treated concrete thereby making it much more resistant to wear and damage. Because of this chemical reaction the pours of the concrete are filled with this by-product and the porosity of the concrete is greatly reduced, not allowing liquids or solids into the concrete, thereby sealing out the contaminates and keeping the pH high.

》》Uses

  CHEMTEC ONE can be used to harden, densify, seal and increase the mass of any concrete infrastructure, such as airport runways and taxiway's, parking facilities, bridges, roads, loading ramps, fueling areas and many other uses. CHEMTEC ONE sealer is designed to deeply penetrate and protect outside concrete infrastructures and is installed after the concrete is fully cured.

CHEMTEC ONE is the only reactive silicate product in the world that meets both the Illinois & Ohio DOT's specification for use on bridge structures and decks.

》》Temperature Limits

  Freshly poured concrete: NONE

Existing concrete: Clean all surfaces so that they are water permeable. Strip off coatings, sealers, paint or anything else that would prevent the CHEMTEC process from penetrating into the concrete. DO NOT ACID WASH CONCRETE. The concrete must be completely dry before you apply the application.

DO NOT ALLOW THIS PRODUCT TO FREEZE. DO NOT APPLY TO WET CONCRETE SURFACES

》》Coverage

  On steel troweled industrial floors the anticipated coverage is approximately 175 to 250 square feet per gallon, and on brushed finish concrete anticipated coverage is 100 to 125 square feet per gallon for each application. Actual coverage will depend on the porosity and temperature of the concrete being treated. It takes two applications to properly protect your porous concrete, and generally only one application on steel troweled surfaces.

 

》》MIXING REQUIREMENTS

  NONE: CHEMTEC ONE comes pre-mixed and ready to use.

Tool cleaning: Clear / Clean up with soap and water immediately after use.

CAUTION: Leaving residue in spraying equipment may damage equipment.


》》Drying Time

  4 hours

Surface may be used as soon as it is completely dry. Do not get surface wet for 12 hours. If used as a curing medium observe normal loads for new concrete.


》》Curing Time

  CHEMTEC ONE starts curing immediately and reaches it full cure in about 75 days. Surface can be used as soon as it is completely dry.

》》APPLICATION METHOD

  Apply by spraying on the surface, saturating the surface. Keep material from puddling, if necessary by spreading it around bristle brooms. Areas that puddle should be brushed over to dryer areas, areas that dry prematurely should have more material pushed to it or be re-sprayed. After the material has been on the steel troweled floor for 35 to 45 minutes then squeegee off the surface. On brushed finished surfaces, just let it dry.(see installation instructions for details ).

CAUTION! DO NOT ALLOW AREAS TO PUDDLE AND DRY, AS THEY WILL LEAVE A HARD WHITE CRYSTAL ON THE SURFACE WHEN DRY ON STEEL TROWELED SURFACES.


》》TOOLS NEEDED

  Low pressure sprayers, bristle brooms, squeegees, safety equipment and so on.

》》STORAGE LIFE

  Up to 24 months. Do not allow product to freeze or be stored in temperatures above 120 º F or below 38º F. Agitate barrel if stored for periods over 3 months

》》CAUTION

  DO NOT store in aluminum containers or use spraying equipment with aluminum fittings. Product may react with the aluminum to create flammable hydrogen gas. See MSDS sheet. DO NOT spray or splash on glass, painted surfaces or decorative fronts as product may stain these surfaces. If you do splash the product on these surfaces wipe off with fresh water immediately. Make sure you have adequate ventilation. Dispose of waste properly per federal, state or local environmental regulations if required.

》》TECHNICAL DATA

  For complete information, pleaserefer to the MSDS (material safety test sheet), technical data sheet or Chemtec One's construction procedures for various specific surfaces, which can be viewed on the US official website: www.concretesealer.net

》》WHAT THE CHEMTEC ONE PROCESS CAN DO:

           1)Reduce the porosity of existing concrete & effectively seal out contaminants.

            2)Increase the surface hardness and Abrasion Resistance of new and deteriorated concrete.

            3)Increase Compression Strength of new and deteriorated concrete.

            4)Reduce Chloride Penetration.

            5)Inhibit chemical attack of treated concrete.

            6)Form a solid by-product in the micro cracks and gel pores.

            7)Retard scaling of high strength properly finished concrete

            8)Increase the Mass & Density of concrete

            9)Produce a sheen on dense steel troweled non-air entrained concrete floors over time.

》》WHAT THE CHEMTEC ONE PROCESS WILL NOT DO.

          1)Make good concrete out of bad concrete.

           2)Correct structural deficiencies.

           3)Correct substrate or erosion problems.

 

 肯泰克国际工厂